RUT955 cung cấp hai khe SIM, 4 cổng Ethernet và Wi-Fi kết hợp với giao diện RS232, RS485, USB và đầu vào/đầu ra cho nhiều ứng dụng đáng kinh ngạc. Bộ định tuyến này đi kèm với các tính năng phần mềm nâng cao của RutOS như Modbus, SNMP, TR-069, NTRIP, hỗ trợ giao thức MQTT và khả năng theo dõi GNSS.
| MOBILE |
| Mobile module |
4G (LTE) – Cat 4 up to 150 Mbps, 3G – Up to 42 Mbps, 2G – Up to 236.8 kbps |
| SIM switch |
2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail, SIM idle protection |
| Status |
Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, Bytes sent/received, connected band, IMSI, ICCID |
| SMS |
SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP |
| USSD |
Supports sending and reading Unstructured Supplementary Service Data messages |
| Black/White list |
Operator black/white list |
| Multiple PDN |
Possibility to use different PDNs for multiple network access and services |
| Band management |
Band lock, Used band status display |
| APN |
Auto APN |
| Bridge |
Direct connection (bridge) between mobile ISP and device on LAN |
| Passthrough |
Router assigns its mobile WAN IP address to another device on LAN |
| WIRELESS |
| Wireless mode |
802.11 b/g/n, 2x2 MIMO, Access Point (AP), Station (STA) |
| WiFi security |
WPA2-Enterprise - PEAP, WPA2-PSK, WEP, WPA-EAP, WPA-PSK; AES-CCMP, TKIP, Auto Cipher modes, client separation |
| SSID/ESSID |
SSID stealth mode and access control based on MAC address |
| WiFi users |
Up to 100 simultaneous connections |
| Wireless Hotspot |
Captive portal (Hotspot), internal/external Radius server, built in customizable landing page |
| ETHERNET |
| WAN |
1 x WAN port 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX |
| LAN |
3 x LAN ports, 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX |
| NETWORK |
| Routing |
Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, RIPng, OSPF6) |
| Network protocols |
TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPnP, SSH, DHCP, Telnet client, SNMP, MQTT, Wake On Lan (WOL) |
| VoIP passthrough support |
H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets |
| Connection monitoring |
Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection |
| Firewall |
Port forward, traffic rules, custom rules |
| DHCP |
Static and dynamic IP allocation, DHCP Relay, Relayd |
| QoS / Smart Queue Management (SQM) |
Traffic priority queuing by source/destination, service, protocol or port, traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e |
| DDNS |
Supported >25 service providers, others can be configured manually |
| Network backup |
VRRP, Mobile, Wired and WiFi WAN options, each of which can be used as backup, using automatic Failover |
| Load balancing |
Balance your internet traffic over multiple WAN connections |
| SSHFS |
Possibility to mount remote file system via SSH protocol |
| SECURITY |
| Authentication |
Pre-shared key, digital certificates, X.509 certificates |
| Firewall |
Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T |
| Attack prevention |
DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks) |
| VLAN |
Port and tag based VLAN separation |
| Mobile quota control |
Custom data limits for both SIM cards |
| WEB filter |
Blacklist for blocking out unwanted websites, whitelist for specifying allowed sites only |
| Access control |
Flexible access control of TCP, UDP, ICMP packets, MAC address filter |
| Secure Boot |
Cryptographic integrity check of the each system boot process (available on device with special order code RUT955T073B0). |
| VPN |
| OpenVPN |
Multiple clients and server can be running simultaneously, 12 encryption methods |
| OpenVPN Encryption |
DES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC, AES-192-CBC, AES-256-CBC |
| IPsec |
IKEv1, IKEv2, supports up to 4 x VPN IPsec tunnels (instances), with 5 encryption methods (DES, 3DES, AES128, AES192, AES256) |
| GRE |
GRE tunnel |
| PPTP, L2TP |
Client/Server services can run simultaneously |
| Stunnel |
Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the programs' code |
| DMVPN |
Method of building scalable IPsec VPNs |
| SSTP |
SSTP client instance support |
| ZeroTier |
ZeroTier VPN client support |
| WireGuard |
WireGuard VPN client and server support |
| MODBUS TCP SLAVE |
| ID range |
Respond to one ID in range [1;255] or any |
| Allow Remote Access |
Allow access through WAN |
| Custom registers |
MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Slave functionality |
| MODBUS TCP MASTER |
| Supported functions |
01, 02, 03, 04, 05, 06, 15, 16 |
| Supported data formats |
8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC) |
| MODBUS RTU MASTER (RS232) |
| Supported baud rates |
From 300 to 115200 |
| Supported functions |
01, 02, 03, 04, 05, 06, 15, 16 |
| Supported data formats |
8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII |
| Number of data bits |
From 5 to 8 |
| Number of stop bits |
1 or 2 |
| Parity |
None, Even, Odd |
| Flow |
None, RTS/CTS, Xon/Xoff |
| Duplex |
Full duplex |
| MODBUS RTU MASTER (RS485) |
| Supported baud rates |
From 300 to 300000 |
| Supported functions |
01, 02, 03, 04, 05, 06, 15, 16 |
| Supported data formats |
8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII |
| Number of data bits |
8 |
| Number of stop bits |
1 |
| Parity |
None, Even, Odd |
| Flow |
None, Xon/Xoff |
| Duplex |
Half duplex |
| MODBUS DATA TO SERVER |
| Protocol |
HTTP(S), MQTT, Azure MQTT |
| MQTT GATEWAY |
| MQTT gateway |
Allows sending commands and receiving data from MODBUS Master through MQTT broker |
| DNP3 |
| Supported modes |
TCP Master, DNP3 Outstation |
| MONITORING & MANAGEMENT |
| WEB UI |
HTTP/HTTPS, status, configuration, FW update, CLI ,troubleshoot, event log, system log, kernel log |
| FOTA |
Firmware update from sever, automatic notification |
| SSH |
SSH (v1, v2) |
| SMS |
SMS status, SMS configuration, send/read SMS via HTTP POST/GET |
| Call |
Reboot, Status, WiFi on/off, Mobile data on/off, Output on/off |
| TR-069 |
OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem |
| MQTT |
MQTT Broker, MQTT publisher |
| SNMP |
SNMP (v1, v2, v3), SNMP trap |
| JSON-RPC |
Management API over HTTP/HTTPS |
| MODBUS |
MODBUS TCP status/control |
| RMS |
Teltonika Remote Management System (RMS) |
| IoT PLATFORMS |
| Cloud of Things |
Allows monitoring of: Device data, Mobile data, Network info, Availability |
| ThingWorx |
Allows monitoring of: WAN Type, WAN IP Mobile Operator Name, Mobile Signal Strength, Mobile Network Type |
| Cumulocity |
Allows monitoring of: Device Model, Revision and Serial Number, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength, WAN Type and IP |
| Azure IoT Hub |
Can send device IP, Number of bytes send/received/ 3G connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, Sim State, PIN state, GSM signal, WCDMA RSCP WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type, Temperature, PIN count to Azure IoT Hub server |
| SYSTEM CHARACTERISTICS |
| CPU |
Atheros Wasp, MIPS 74Kc, 550 MHz |
| RAM |
128 MB, DDR2 |
| FLASH storage |
16 MB, SPI Flash |
| FIRMWARE / CONFIGURATION |
| WEB UI |
Update FW from file, check FW on server, configuration profiles, configuration backup, restore point |
| FOTA |
Update FW/configuration from server |
| RMS |
Update FW/configuration for multiple devices |
| Keep settings |
Update FW without losing current configuration |
| FIRMWARE CUSTOMIZATION |
| Operating system |
RutOS (OpenWrt based Linux OS) |
| Supported languages |
Busybox shell, Lua, C, C++ |
| Development tools |
SDK package with build environment provided |
| LOCATION TRACKING |
| GNSS |
GPS, GLONASS, BeiDou, Galileo and QZSS |
| Coordinates |
GNSS coordinates via WebUI, SMS, TAVL, RMS |
| NMEA |
NMEA 0183 |
| NTRIP |
NTRIP protocol (Networked Transport of RTCM via Internet Protocol) |
| Server software |
Supported server software TAVL, RMS |
| Geofencing |
Configurable multiple geofence zones |
| SERIAL |
| RS232 |
DB9 connector, full RS232 (with RTS, CTS) |
| RS485 |
RS485 Full Duplex (4 wires) and Half Duplex (2 wires). 300-115200 baud rate |
| Serial functions |
Console, Serial over IP, Modem, MODBUS gateway, NTRIP Client |
| USB |
| Data rate |
USB 2.0 |
| Applications |
Samba share, USB-to-serial |
| External devices |
Possibility to connect external HDD, flash drive, additional modem, printer |
| Storage formats |
FAT, FAT32, NTFS |
| INPUT / OUTPUT |
| Input |
1 x digital dry input (0 - 3 V), 1 x digital galvanically isolated input (0 - 30 V), 1 x analog input (0 - 24 V), 1 x Digital non-isolated input (on 4-pin power connector, 0 - 5 V detected as logic low, 8 - 30 V detected as logic high) |
| Output |
1 x digital open collector output (30 V, 250 mA), 1 x SPST relay output (40 V, 4 A), 1 x Digital open collector output (30 V, 300 mA, on 4-pin power connector) |
| Events |
Email, RMS, SMS |
| I/O juggler |
Allows to set certain I/O conditions to initiate event |
| SD CARD |
| Physical size |
Micro SD |
| Applications |
Samba share, Storage Memory Expansion, DLNA |
| Capacity |
Up to 64 GB |
| Storage Formats |
FAT32, NTFS, ext2, ext3, ext4 |
| POWER |
| Connector |
4 pin industrial DC power socket |
| Input voltage range |
9 – 30 VDC, reverse polarity protection, surge protection >33 VDC 10us max |
| PoE (passive) |
Passive PoE over spare pairs (available from HW revision 0007 and batch number 0010). Possibility to power up through LAN port, not compatible with IEEE802.3af, 802.3at and 802.3bt |
| Power consumption |
< 2 W idle, < 7 W Max |
| PHYSICAL INTERFACES (PORTS, LEDS, BUTTONS, SIM) |
| Ethernet |
4 x RJ45 ports, 10/100 Mbps |
| I/O’s |
2 x Inputs and 2 x Outputs on 10-pin industrial socket, 1 x Digital input and 1 x Digital output on 4-pin power connector (available from HW revision 1600) |
| Status LEDs |
1 x bi-color connection status LED, 5 x connection strength LEDs, 4 x LAN status LEDs, 1 x Power LED |
| SIM |
2 x SIM slots (Mini SIM - 2FF), 1.8 V/3 V, external SIM holders, eSIM (Optional) |
| Power |
1 x 4 pin DC connector |
| Input/output |
1x 10 pin industrial socket for inputs/outputs |
| Antennas |
2 x SMA for LTE, 2 x RP-SMA for WiFi |
| USB |
1 x USB A port for external devices |
| RS232 |
1 x DB9 socket |
| RS485 |
1 x 6-pin industrial socket |
| Reset |
Reboot/User default reset/Factory reset button |
| PHYSICAL SPECIFICATION |
| Casing material |
Aluminium housing with DIN rail mounting option, plastic panels |
| Dimensions (W x H x D) |
110 x 50 x 100 mm |
| Weight |
287 g |
| Mounting options |
Bottom and sideways DIN rail mounting slots |
| OPERATING ENVIRONMENT |
| Operating temperature |
-40 °C to 75 °C |
| Operating humidity |
10% to 90% non-condensing |
| Ingress Protection Rating |
IP30 |